+1 716 309 2066+1 815 664 3282

Embroidery Size Chart and Placement Guide

Standard embroidery sizes: a left chest logo is 3.5 to 4 in wide, a cap front is 4.5 x 2.25 in (no taller than 2.5 in on structured caps), a sleeve logo is 3 x 2 in and a full back is 10 to 12 in wide. Check your logo size below to see if it fits, then print the chart. Free, no sign-up.

Check if your logo fits

1. Where will the logo go?

2. Your logo size (optional)

Measure the widest and tallest points of the logo itself, not the image file.

Embroidery size chart

Standard is the size that looks right on most garments. Largest is the most the spot can hold before the logo runs into seams, plackets or the cap brim. Sizes are width x height.

Standard and largest embroidery sizes by placement
PlacementStandard sizeLargestWhere it goes
Left or right chestPolos, shirts, jackets3.5 x 2 to 4 x 4 in4.5 x 4.5 in7 to 9 in below the shoulder seam, centered between placket and side seam
PocketShirt or polo pocket2 x 2 to 3 x 3 inSet by your hoopCentered on or just above the pocket, 0.5 in inside the edges
Cap front, structuredStiff front caps4.5 x 2.25 in5 x 2.5 inCentered over the front seam, close to the brim
Cap front, unstructuredSoft dad hats4.5 x 2.25 in5.5 x 2.75 inCentered on the front panel, close to the brim
Cap sideSide panel2 x 1 in2.5 x 1.5 inCentered on the side panel, clear of the seams
Cap backAbove the closure3 x 0.75 to 4 x 1 in4 x 1.25 inCentered above the back arch
Beanie cuffFolded cuff3.5 x 1.75 in4.25 x 2 inCentered on the cuff, under the fold
Sleeve, upper armSmall sleeve logo3 x 2 in4 x 4 inCentered on the outside of the upper arm
Sleeve, vertical textDown the arm2.5 x 10 in3 x 14 inDown the arm, at least 2 in from cuff and shoulder seam
Shirt cuffInitials1.5 x 0.5 in2.5 x 1 inCentered on the cuff band, clear of buttonholes
Back yokeBelow the collar3 x 1.5 to 4 x 2 in5 x 3 inCentered, 1 to 2 in below the collar seam
Center frontHoodies and tees8 x 8 to 9 x 9 in10 x 12 inCentered, 3 to 4 in below the neckline
Full backJackets, hoodies10 x 10 to 11 x 11 in12 x 14 inCentered, top about 2 in below the collar
PatchSew-on or iron-on2 x 2 to 4 x 4 inSet by your hoopSized to fit the spot it will be sewn on
Tote bagFront panel5 x 5 inSet by your hoopCentered on the front panel
TowelAbove the border5 x 4 inSet by your hoopCentered, 2 to 3 in above the woven border

Youth and small sizes: go about 0.5 in smaller than the standard chest size. Sizes are a guide; your digitizer checks every design for its garment.

Where to place embroidery

Placement is measured on the garment laid flat. These are the positions our digitizers and most embroidery shops use.

Left chest

About 7 to 9 in down from the left shoulder seam, centered between the placket and the side seam, or 4 to 6 in from the placket. On polos, keep the logo clear of the buttons.

Cap front

Centered over the front seam and as close to the brim as the frame allows. Stay inside the front panel seams on both sides.

Cap back and side

Cap back sits centered above the closure arch, so measure the space above the opening first. Side logos stay small because the panel curves.

Full back

Centered between the side seams, with the top of the design about 2 in below the collar seam. Upper-back text across the shoulders can run up to about 10 x 4 in.

Sleeve

Upper arm logos sit centered on the outside of the sleeve. Vertical text runs down the arm and stops at least 2 in before the cuff or shoulder seam.

Center front

Centered between the side seams, starting about 3 to 4 in below the neckline. On hoodies, the front pocket limits the height.

Smallest text you can embroider

Use 0.25 in (6 mm) tall block letters for the cleanest result, and 0.3 in (8 mm) for script or serif fonts. With careful manual digitizing, simple block text can go down to about 0.16 in (4 mm). Smaller than that, letters fill in and thread breaks. Small letter digitizing

Minimum embroidery text heights
LetteringBest heightSmallest
Block (sans serif) capitals0.25 in (6 mm)0.16 in (4 mm)
Script and serif fonts0.3 in (8 mm)0.25 in (6 mm)
Lowercase letters0.3 in (8 mm)0.2 in (5 mm)

Home embroidery machine hoop sizes

The hoop's stitch field is the largest design your machine can sew in one go. Brother, Janome, Bernina and Baby Lock home machines use these common sizes. Commercial multi-needle machines take much larger frames, including jacket back frames for designs up to 12 x 14 in.

Common home machine hoop sizes
HoopStitch fieldGood for
4 x 4 in100 x 100 mmLeft chest, caps (with cap frame), patches, names
5 x 7 in130 x 180 mmBigger chest logos, towels, tote bags
6 x 10 in160 x 260 mmCenter front, vertical sleeve text
8 x 8 in200 x 200 mmSquare center front designs
8 x 12 in200 x 300 mmSmall back designs, large front designs

Tell us your hoop when you order and we fit the file to it, or split a large design into hoopings.

How size affects the digitizing price

Bigger designs have more stitches, so they cost more to digitize. A left chest or cap logo is $15 to $25 flat, a center front design $20 to $50 and a full back $20 to $75. You can also pay $1 per 1,000 stitches ($7 minimum). See your exact price in the embroidery price calculator.

How to measure your logo

  1. 1

    Measure the logo, not the file

    Use the widest and tallest points of the design. Empty space around the logo in the image doesn't count.

  2. 2

    Lay the garment flat

    Measure placement on a flat garment. For caps, use a flexible tape across the curved front panel.

  3. 3

    Leave a margin

    Keep at least 0.5 in between the logo and any seam, placket, pocket edge or zipper.

Digitized for the size you need

Every file is digitized by hand for its exact size and fabric, then checked on a PNG stitch preview before you pay. Sassy Digitizing has served 2,168+ clients and is rated 4.9/5 on Google and 4.8/5 on Trustpilot.

Frequently Asked Questions

Everything you need to know about our embroidery digitizing service, pricing, file formats, turnaround times and revision policy.

What is the standard size for a left chest embroidery logo?

A left chest logo is usually 3.5 to 4 inches wide, with a height of 2 to 4 inches depending on the logo's shape. The largest that fits is about 4.5 x 4.5 inches. Place it 7 to 9 inches down from the left shoulder seam, centered between the placket and the side seam.

What size should a cap front logo be?

A structured cap front logo is usually 4.5 inches wide and 2.25 inches tall, and no more than 5 x 2.5 inches. Soft unstructured caps can take up to about 5.5 x 2.75 inches. Taller designs run into the crown or the brim.

How big is a jacket back embroidery design?

A full back design is usually 10 to 11 inches wide and tall, and up to 12 x 14 inches on a jacket frame. Center it between the side seams, with the top about 2 inches below the collar.

What size is a sleeve logo?

An upper-arm sleeve logo is usually 3 x 2 inches and no bigger than 4 x 4 inches. Vertical text down the arm can be 2.5 to 3 inches wide and up to 14 inches long.

What size should a pocket logo be?

A pocket logo is usually 2 to 3 inches wide, staying at least 0.5 inches inside the pocket edges.

What is the smallest text you can embroider?

Block letters look best at 0.25 inches (6 mm) tall or more, and script or serif fonts at 0.3 inches (8 mm). Careful manual digitizing can take simple block text down to about 0.16 inches (4 mm).

What are the common embroidery hoop sizes?

Home machines usually use 4 x 4, 5 x 7, 6 x 10, 8 x 8 or 8 x 12 inch hoops. The hoop's stitch field, such as 100 x 100 mm for a 4 x 4 hoop, is the largest design it can sew in one go.

Does a bigger design cost more to digitize?

Yes, because it has more stitches. A left chest or cap logo is $15 to $25 flat, a center front design $20 to $50 and a full back $20 to $75, or $1 per 1,000 stitches with a $7 minimum.

What if my logo is bigger than the standard size?

The checker tells you if it still fits the spot. If it's too big, we can digitize it at a size that fits, or at your custom size if your garment allows it.

How do I measure my logo for embroidery?

Measure the widest and tallest points of the logo itself, not the image file. Then check it against the chart for the spot it will go.